Assessing the quality of liquid milk is done through performing quality assurance tests, which begin by sampling of the liquid milk. It is important for safety and economic reasons. All dairy products must be tested for quality assurance purposes.
Sampling facilitates comprehensive analysis of any given product for quality assurance. A sample represents the quality of the entire volume of the product under consideration.
Sampling is necessary because it is practically impossible to test the whole batch. We will examine some of the reasons why quality assessment is important, especially in the dairy industry and some important things to consider while doing this.
It is important to carry out a proper sampling to obtain accurate results.
Sampling: - drawing out of a portion of substance/material from the total population
Population: - total quantity of material whose characteristics you are seeking through sampling
Sample: - a small portion of the population which you obtain in such a way as to represent the characteristics of that particular population as closely as possible. Only a representative sample will produce consistent results.
You can have a single sample from different sub-samples, which you collect from different parts of the population. You get a representative sample by randomly drawing from the population.
Random sample: - a random sample occurs when every object in the population has an equal chance of selection
Biased sample: - a sample where some objects in the population have unlikely chance of selection
Laboratory sample: - when a sample is too large for a normal lab examination procedure, you take its fraction. This fraction is the lab sample.
The primary objective of sample selection is to ensure that the features of the lab sample represent the population.
It is necessary to limit sample size to cut down on time, cost, and personnel required for that analytical work. Limited samples exhibit limited estimates of the whole population.
This equipment is useful for attaining consistency in the milk/cream for a representative sampling of these dairy products. It is made of stainless steel, aluminium or any other metal that does not adversely affect the milk.
It consists of a perforated disk with a long handle fixed at its center to help in moving the equipment through the milk to achieve effective mixing.
Consists of a small cup fixed to one end of a long handle. It is mainly used to collect sample from the container. They vary in capacity.
Consists of an open ended tube with provision for closing one of the ends. It has the following advantages:
Sampling of milk and milk products differs in terms of materials you use and the purpose of the sample.
Sample selection is necessary because the destruction of the population occurs over time. The process is also tedious and time consuming.
A sampling plan is necessary because it ensures that the lab sample is truly representative of the entire population.
You should clearly write down your sampling plan in a document that contains the details the analyst will use. Such details may include the sample size, the population, method of collection, and preservation methods.
The sampling plan should also stipulate the required documentation of the sampling procedures. The choice of sampling plan will depend on:
More details on sampling plan discussed below.
Analysis is done for various reasons, which will affect the sampling plan. They include:
Necessary for legal requirements by government labs. This ensures that the suppliers/producers/manufacturers produce safe products that meet legal and labeling requirements e.g. whole milk sampling for butterfat content determination.
Necessary to ascertain the quality of materials a factory uses for processing are compliant. This ensures that the material will withstand the manufacturing processes.
Quality of the products depends on the quality of the raw materials used for making them
Samples analyzed during processing to ensure that the process is operating in an effective manner. It aims at detecting problems and adjusting accordingly to end up with good quality products.
Techniques used in process controls should produce process results within a short time. This can be done in the following two ways:
Aims at ensuring that the finished products are safe and they meet legal requirements
Specify the particular property you want to analyze e.g. fat content, microbial load, developed acidity, etc. You can classify these properties as either attributes or variables.
i) Attributes: - properties that a product should either have or not.
ii) Variables: - properties that you can measure on a continuous scale such as the butter fat content, weight, moisture content of milk powder, etc.
Variable sampling requires less samples than attribute samples. The type of property measured should determine the seriousness of the outcome (such as when measuring for harmful microorganisms, there is need for high precision due to the danger it poses than when measuring for fat content).
i) Finite population: - has a defined size e.g. tanker full of milk.
ii) Infinite population: - has no defined size e.g. sampling from a conveyor belt which continuously supply the product e.g. packaging machine.
Analysis of finite population provides properties about that population. Analysis from an infinite population gives information about the processes.
Therefore, to facilitate sampling population, it is convenient to divide the infinite population into a number of finite populations e.g. all products produced in one shift forms one finite population. This will help to trace the source of problems in the process.
iii) Continuous population: - no physical separation between the different parts of the sample e.g. well stirred milk in a tanker
iv) Compartmentalized: - split into a number of separate sub-units
v) Homogeneous: - properties of an individual sample is the same as those of the other samples in different regions of the population
vi) Heterogeneous: - characteristics of one sample vary within different locations of the population e.g. raw milk and its butterfat content; a well stirred milk is homogeneous while standing milk is heterogeneous.
Practically, most samples are heterogeneous hence the importance of selecting samples from different locations. You will then mix the parts well to obtain a representative sample.
Test procedure usually takes into account:
When you realize that the procedure is cheap, rapid and non-destructive, take more samples. More samples increases accuracy of the results you intend to achieve by sampling dairy products for analysis.
After looking at the factors to be considered when sampling milk, it is now possible to draft a sampling plan. The sampling plan has a specific objective of ensuring that a the obtained sample will be reflective of the qualities that one is seeking to establish about the group.
The plan will clearly indicate the size of the sample and all the important features for examination under every group.
No problem when dealing with homogenous population; however, heterogenous population requires consideration of the sampling plans e.g.
State clearly whether the sampling will be manual or by specialized mechanical devices
These are the steps to follow:
Most samples are heterogenous due to inter-unit variation or intra-unit variation.
Inter-unit variation – variation of properties in different units e.g. milk fat content variations that occur in different milk cans
Intra-unit variation – variation within individual units, e.g. fat content variation in one milk can.
Smaller sample sizes are easier to manage during analysis, which reduces the chances of sample contamination and cross-contamination.
Ensure the sample does not undergo physical, chemical, or enzymatic changes. Enzymatic changes should be countered by elimination or inactivation of the enzyme, which can be achieved through:
Fat oxidation is the most likely chemical change to occur on fat based dairy products such as cream, ghee (products with unsaturated fatty acids). To reduce oxidation, limit such samples to light exposure, elevated temperature, oxygen, or from co-oxidants.
Prevent microbial growth through freezing, cold storage, heat treatment, and use of preservatives.
Physical changes likely to occur may include loss or gain of moisture, which can affect butter analysis. Another serious physical change may also include crystallization (as in the case of ice cream samples). You will be able to control most of the physical changes by monitoring the storage temperature and relative humidity.
Carefully label all the laboratory samples so that in case of any problem, it is easy to trace the origin. The information that is usually used for the identification of laboratory samples includes:
The objective of raw milk quality assessment is to ascertain the quality of the finished product. You have to make sure that you are starting off with the best quality raw milk so that you can assure the consumers that the quality of the finished product is the best.
Since you are dealing with large quantities of milk, it is necessary to take a representative sample from which you will be able to determine the quality of the entire batch. This is why you will need to do sampling of liquid milk.
At the dairy processing plant, you will be receiving milk in single batches, either from individual farmers or from bulking stations. You will need to obtain samples from these single containers.
To do this, mix the milk mechanically and then draw the required quantity of sample. Label the sample container appropriately and follow the general sample handling procedures.
A composite sample is the quantity of milk obtained by mixing proportional parts of different milks. A sample is then picked from the composite sample to represent the whole lot.
Storage tanks usually have agitators used to mix the milk. Ensure the milk is mixed gently for about 15 minutes in the tank and in case there are no mechanical agitators, mix the milk mechanically using a stirrer and then pick the sample using a dipper.
Pick the samples proportionate to the size of the tank. The minimum amount of the sample should be at least 500 mls.
Most modern tanks and tankers have automatic samplers from which you obtain the sample after the contents have been uniformly mixed.
Cream is thicker than fluid milk; therefore, the tester should use a sampling tube with a wider diameter. It is important to ensure that the cream has been properly mixed before picking the samples.
Make sure to examine the samples soon after collection as any delay may lead to deterioration in the sample quality. This is due to the susceptibility of cream to enzymatic degradation given its high butter fat content. This could jeopardize the results.
Put the unopened cans in a water bath at 60°C for two hours. You will need to remove the cans from the water bath every 20 minutes for a vigorous shaking.
After the two hours have elapsed, remove the cans and cool to room temperature. Remove the lid and mix the content with a spatula. At this point, you can get a composite sample from different cans.
Depending on the type of tests to be done, you can test the sample the way it is or you can mix with distilled water. The value obtained from the test is adjusted using a correction factor.
Temper the unopened cans in a water bath at 35°C for 30 minutes. After the time has elapsed, empty all the contents of the container while still warm and mix to a uniform consistency.
Take 100 grams of the sample and mix with 500 grams of distilled water in a water bath. Get a test sample from the diluted mixture for testing and correct using the dilution factor used.
Avoid sampling in a high humidity environment. Take samples from different parts/regions of the mass to be tested using a tubular trier and then transfer the collected samples to a dry clean container and seal immediately.
Roll and invert the container to make the sample homogeneous. If there are lumps, sieve the sample, grind the residue and sieve again. Test immediately or keep the sample in an airtight container for analysis at a later date.
Under some circumstances, it may be necessary to keep the sample in an opaque container.
Take samples from a batch of bulk butter using a stainless steel trier from the different sections, which you will then mix to obtain a homogeneous sample.
You may soften the samples by warming in a water bath at 38°C while checking the sample regularly during this process. After it has obtained the required texture, weigh the required quantity and carry out the tests.
When you are sampling packaged butter, pick packets from different areas in the storage room. Combine all these samples together to obtain a homogeneous mix from which you will get the test sample.
For small pieces of cheese take the entire cheese block while for the larger cheese blocks, obtain samples using triers that reach into the centre of the cheese block.
For hand cheese, cut or shred the cheese using a food chopper then mix before getting a representative sample.
Allow the sample to soften to room temperature and then mix for about two minutes in a blender. Obtain the test sample and conduct the required test procedure.
If the ice cream or the frozen dairy product contains fruits and/or nuts, mix in a high speed blender for about seven minutes to make sure that it is fully homogeneous before obtaining the test sample for conducting the required tests.
For retail packages, pick a number of packages but for bulk packaging, mix the bulk and take 500 mls as a representative sample.
When sampling from closed systems (e.g. UHT), there will be an inbuilt sampling equipment or mechanism on the system for taking the samples aseptically.
Milk sampling is the first step one takes when working towards identifying a problem with the milk or the animal that produced that milk. Aseptic technique will help you ensure that you do not expose the milk to contamination/cross-contamination.
The individual carrying out the sampling activity should be extra careful to adhere to all the procedures for sample collection.
Certain diseases associated with milk, e.g. mastitis or tuberculosis, may result from the bacteria from the animal or the handler.
Aseptic technique will also help you correctly identify the causative organisms to facilitate proper administration of correct medication.
These causative microorganisms can come from the cows' skin, udder, and teats as well as on the hands of the sampler. Do not forget about the barn/cowshed environment.
Contamination of samples will result in misdiagnosis, which will cause increased production costs, confusion, and frustration.
One can be able to avoid contamination during sampling by following the following procedures: